KATRON TECHNOLOGIES, INC. 10BASE-T ETHERNET ADAPTER (16-BIT) NIC Type Ethernet Transfer Rate 10Mbps Data Bus 16-bit ISA Topology Star Wiring Type Unshielded twisted pair AUI transceiver via DB-15 port Boot ROM Available [Image] ETHERNET VERSION Version JP1 » Version 2 Pins 1 & 2 closed Version 1 Pins 2 & 3 closed LINK INTEGRITY TEST Setting JP2 » Enabled Pins 1 & 2 Closed Disabled Pins 2 & 3 Closed Note:The link integrity test is only valid when the cable type is unshielded twisted pair. CABLE TYPE Type JP3 » Unshielded twisted pair Pins 2 & 3 closed AUI transceiver via DB-15 port Pins 1 & 2 closed I/O BASE ADDRESS Address JP4A JP4B JP4C JP4D 200h Pins 2 & 3 Open Open Open closed 220h Open Pins 2 & 3 Open Open closed 240h Open Open Pins 2 & 3 Open closed 260h Open Open Open Pins 2 & 3 closed 300h Pins 1 & 2 Open Open Open closed 320h Open Pins 1 & 2 Open Open closed 340h Open Open Pins 1 & 2 Open closed 360h Open Open Open Pins 1 & 2 closed BOOT ROM ADDRESS Address JP5A JP5B JP5C JP5D JP5E C0000h Pins 1 & Pins 1 & Pins 1 & Pins 1 & Pins 1 & 2 2 2 2 2 C2000h Pins 2 & Pins 1 & Pins 1 & Pins 1 & Pins 1 & 3 2 2 2 2 C4000h Pins 1 & Pins 2 & Pins 1 & Pins 1 & Pins 1 & 2 3 2 2 2 C6000h Pins 2 & Pins 2 & Pins 1 & Pins 1 & Pins 1 & 3 3 2 2 2 C8000h Pins 1 & Pins 1 & Pins 2 & Pins 1 & Pins 1 & 2 2 3 2 2 CA000h Pins 2 & Pins 1 & Pins 2 & Pins 1 & Pins 1 & 3 2 3 2 2 CC000h Pins 1 & Pins 2 & Pins 2 & Pins 1 & Pins 1 & 2 3 3 2 2 CE000h Pins 2 & Pins 2 & Pins 2 & Pins 1 & Pins 1 & 3 3 3 2 2 D0000h Pins 1 & Pins 1 & Pins 1 & Pins 2 & Pins 1 & 2 2 2 3 2 D2000h Pins 2 & Pins 1 & Pins 1 & Pins 2 & Pins 1 & 3 2 2 3 2 D4000h Pins 1 & Pins 2 & Pins 1 & Pins 2 & Pins 1 & 2 3 2 3 2 D6000h Pins 2 & Pins 2 & Pins 1 & Pins 2 & Pins 1 & 3 3 2 3 2 » D8000h Pins 1 & Pins 1 & Pins 2 & Pins 2 & Pins 1 & 2 2 3 3 2 DA000h Pins 2 & Pins 1 & Pins 2 & Pins 2 & Pins 1 & 3 2 3 3 2 DC000h Pins 1 & Pins 2 & Pins 2 & Pins 2 & Pins 1 & 2 3 3 3 2 Note: Pins designated should be in the closed position. BOOT ROM Setting JP5F » Disabled Pins 2 & 3 Closed Enabled Pins 1 & 2 Closed INTERRUPT REQUEST IRQ JP6A JP6B JP6C JP6D JP6E JP6F JP6G 2/9 Open Open Open Open Open Open Closed 3 Open Open Open Open Open Closed Open 4 Open Open Open Open Closed Open Open 5 Open Open Open Closed Open Open Open 10 Open Open Closed Open Open Open Open 11 Open Closed Open Open Open Open Open 12 Closed Open Open Open Open Open Open COMPATIBILITY MODE Setting JP7 » Disabled Pins 1 & 2 closed Enabled PIns 2 & 3 closed Note:On some systems the data bus timing is not truly IBM PC/AT compatible. If the card is not initializing, enabling compatibility mode may allow the card to operate properly. [Image] DIAGNOSTIC LED(S) LED Status Condition LED1 On Twisted pair network connection is good LED1 Off Twisted pair is not connected/Link test disabled LED1 Blinking Twisted pair network connection is broken LED2 Off Normal operation LED2 On Twisted pair receive wires are reversed and corrected LED3 Blinking Data is being transmitted or received LED3 Off Data is not being transmitted or received LED3 On Card is malfunctioning LED4 Off Normal operation LED4 On Collision detected on network Note:If the twisted pair receive wires are reversed the card will automatically detect this and correct for the reversal. It is strongly recommended that the wires be corrected as soon as possible. CONNECTORS Function Location External Transmit/Receive LED JP9 Note:The external TX/RX LED will function identically to LED3.